shop seals gun parts news showroom HyperMagnum pistol Eleven pistol rare airguns range test work shop f.a.q. terms of ordering design studies airgun talk compendium of terminology ballistics calculators & unit converters press room contact site map
shop seals gun parts
news
showroom
HyperMagnum pistol
Eleven pistol
rare airguns
range test
work shop
f.a.q.
terms of ordering
design studies
airgun talk
compendium of terminology
ballistics calculators & unit converters
press room
contact
site map
SHOP Seal kit cal.177 for Smith&Wesson 79G | in stock Seal kit cal.22 for Smith&Wesson 78G | in stock USD 16.00 in stock Shipping (up to 4 kits) USD 4.00 Put an end to the leaking of those otherwise good pistols. Will also fit Daisy 780/790. The kit includes high performace oil-resistant o-rings including a transfer port seal which helps to stop the blow-off and waste of CO2 bypassing the transfer port, resulting in higher velocity! (The original design does not have any seal.) Installation is easy, pin punch required. Comes with instructions, but give it to a gunsmith if you feel uncomfortable. Note: some of our our o-ring dimensions are different from the originals to compensate for the poorly engineered groove dimensions. Guns fitted with our seals hold pressure for several months. Please make sure you order for the correct caliber as seal dimensions differ. •Check Out Piston seal for RWS/Dianawerk Get maximum velocity using our red high performance parachute design piston seal! Top quality polymers and rigorous quality standards ensure highest durability. Unbeatable. 28.6mm diameter; to fit models RWS Dianawerk 24, 26, 28, 34, 36, 38, 40, 45, 46, 48, 52, 54, 56, 60, 66, 75, 300, 350, 460, as well as SM1000 and B21-2. It is strongly recommended to replace the piston seal frequently, as worn out seals are often the cause for broken scopes and loss of power. Instructions on how to replace the seal can be found here. USD 9.00 in stock Shipping (up to 4 items) USD 4.00 •Check Out Replacement piston (part # 62; Kolben) for Walther LP2 and LP3 | in stock After half a century, the piston seals of nearly all Walther LP2 and Walther LP3 are decaying, due to low quality mineral oils or the inferior Ballistol used as a chamber lube. Nowadays, much better products, like synthetic oils, are readily available. Simply install this new design with 2 oil-resistant o-rings. Guns fitted with this piston usually shoot 350fps. 2 replacement seals and installing instructions are provided. Installation is not too difficult. USD 56.00 Shipping USD 18.00 out of stock •Check Out You will be invoiced; pre-payment required. World-wide next day shipping. New! Faster shipping from Europe; EU destinations: 2 to 3 workling days, to US: 4 to 6 working days. SHIPPING AND INVOICE TO: (Please do not type ALL CAPS) *First/last name: *Billing/shipping address: *Postal Code: *Country: *E-mail address: Promo code (if applicable): Comments/Questions:
Seal kit cal.177 for Smith&Wesson 79G | in stock
Seal kit cal.22 for Smith&Wesson 78G | in stock
USD 16.00
in stock
Shipping (up to 4 kits) USD 4.00
Put an end to the leaking of those otherwise good pistols. Will also fit Daisy 780/790. The kit includes high performace oil-resistant o-rings including a transfer port seal which helps to stop the blow-off and waste of CO2 bypassing the transfer port, resulting in higher velocity! (The original design does not have any seal.)
Installation is easy, pin punch required. Comes with instructions, but give it to a gunsmith if you feel uncomfortable. Note: some of our our o-ring dimensions are different from the originals to compensate for the poorly engineered groove dimensions. Guns fitted with our seals hold pressure for several months.
Please make sure you order for the correct caliber as seal dimensions differ.
•Check Out
Piston seal for RWS/Dianawerk
Get maximum velocity using our red high performance parachute design piston seal! Top quality polymers and rigorous quality standards ensure highest durability. Unbeatable.
28.6mm diameter; to fit models RWS Dianawerk 24, 26, 28, 34, 36, 38, 40, 45, 46, 48, 52, 54, 56, 60, 66, 75, 300, 350, 460, as well as SM1000 and B21-2.
It is strongly recommended to replace the piston seal frequently, as worn out seals are often the cause for broken scopes and loss of power.
Instructions on how to replace the seal can be found here.
USD 9.00
Shipping (up to 4 items) USD 4.00
Replacement piston (part # 62; Kolben) for Walther LP2 and LP3 | in stock
After half a century, the piston seals of nearly all Walther LP2 and Walther LP3 are decaying, due to low quality mineral oils or the inferior Ballistol used as a chamber lube. Nowadays, much better products, like synthetic oils, are readily available.
Simply install this new design with 2 oil-resistant o-rings. Guns fitted with this piston usually shoot 350fps.
2 replacement seals and installing instructions are provided. Installation is not too difficult.
USD 56.00
out of stock
You will be invoiced; pre-payment required.
World-wide next day shipping.
New! Faster shipping from Europe; EU destinations: 2 to 3 workling days, to US: 4 to 6 working days.
SHIPPING AND INVOICE TO: (Please do not type ALL CAPS)
*First/last name:
*Billing/shipping address:
*Postal Code:
*Country:
*E-mail address:
Promo code (if applicable):
Comments/Questions:
Web Design © by Blue Line Studios